用于各種金屬、玻璃、陶瓷、石材、電鍍(含水電鍍)、陽極氧化鋁表面及烤(噴)漆面等制品的絲印及移印,不需加固化劑,不需烘烤,即可獲得優異的附著力。
油墨特性:
1、平光、附著力佳、耐汽油、耐化學品;
2、手感好,流平性佳、面光潔;
3、表面硬度好,耐沖擊性能強、抗刮傷;
4、耐汽油、耐酒精、耐化學品程度佳;
印刷:
選用網目為100-350目,以120T網紗計算涂覆蓋面積每公斤達30~35㎡。
表干時間自然揮發5-15分鐘,實干時間在24小時以內,48小時后達**性能。
1.用配套專用稀釋劑開油水
2.用718洗網水洗網。
3.或添加配套硬化劑10%可增加附著力,提高墨膜硬度。
4.烤箱80℃烘烤10分鐘佳能更優。
測試方法(完全干燥后):
1.3M膠紙粘在畫有百格的油墨表面45度角迅速拉起不脫油。
使用方法:
1.建議用我公司專用稀釋劑進行稀釋,不建議使用783慢干稀釋劑稀釋,使用前應充分?jǐn)嚢?用后隨時密封。
2.攪拌時加本公司配套開油水10-12%,稀釋到印刷適合粘度,移印稀釋使用移印專用稀釋劑;用718洗網水清洗。
3.不得與其它類型油墨混合使用,否則容易出現其他附著力,化學反應等不良現象。
4. 加入固化劑的油墨使用時限為8小時,過期請棄用,剩余油墨不可回收
注意事項:
1.各種承印物料的外觀相似,但可能會是不同的材料,客戶需先試印,確其符合要求后,再批量生產。
2.在移印過程中,如出現拉絲或散開,可適當加入一些慢干膏即可;
3.環境溫度過高,將會影響油墨原有質量。白色超越150都會變色,烘烤時請用木質材料墊底進行烘烤,不得直接接觸鐵
4.根據氣候變化,請遠離火源,陰暗處15度-30度環境下存放

Oles MPE Plating Ink

MPE plating strengthening series ink characteristics : mainly used in plating surface, enhanced surface, vacuum plating surface.PU surface.UV surface and other materials, with a high color, high color, high covering power, high stability, high alcohol and rub characteristics. Printing: screen printing can be. Surface drying and drying time: surface dry time natural volatile 5-10 minutes; work time within 24 hours. Dilution and cleaning: SV3 slow dry open water, UVK1 ( printing open water) can be simultaneously used 718 washing network water cleaning. Test method ( completely dry ): 1, 3M gummed paper in the paintings of the surface of the ink, 45 degree angle quickly pulled off the oil; 2, 99% of the purity of industrial alcohol, one kilogram of weight of cotton pack in the ink surface, with a horizontal force pulling back and forth 200 times without decolorization; 3: oak, wear resistance eraser 500g force level brush back and forth 500 times. Usage: 1, use should be fully stirred, use at any time after the closure; 2, add water mixing 10-15%, diluted to 3, screen printing viscosity; the plug is available when washing network water cleaning; 4, not with other types of ink mixing. Note: 1, the plastic material similar in appearance, but may be of different materials, customers need to try to determine its requirements, and then batch printing; 2, in the printing process, such as drawing or spread out, may be appropriate to add some slow dry plaster; 3, the ambient temperature is too high, will affect the quality of the original ink; 4, according to climate change, please stay away from fire, dark environment storage.用于各種金屬、玻璃、陶瓷、石材、電鍍(含水電鍍)、陽極氧化鋁表面及烤(噴)漆面等制品的絲印及移印,不需加固化劑,不需烘烤,即可獲得優異的附著力。

油墨特性:

1、平光、附著力佳、耐汽油、耐化學品;

2、手感好,流平性佳、面光潔;

3、表面硬度好,耐沖擊性能強、抗刮傷;

4、耐汽油、耐酒精、耐化學品程度佳;

印刷:

選用網目為100-350目,以120T網紗計算涂覆蓋面積每公斤達30~35㎡。

表干時間自然揮發5-15分鐘,實干時間在24小時以內,48小時后達**性能。

1.用配套專用稀釋劑開油水

2.用718洗網水洗網。

3.或添加配套硬化劑10%可增加附著力,提高墨膜硬度。

4.烤箱80℃烘烤10分鐘佳能更優。

測試方法(完全干燥后):

1.3M膠紙粘在畫有百格的油墨表面45度角迅速拉起不脫油。

使用方法:

1.建議用我公司專用稀釋劑進行稀釋,不建議使用783慢干稀釋劑稀釋,使用前應充分?jǐn)嚢?用后隨時密封。

2.攪拌時加本公司配套開油水10-12%,稀釋到印刷適合粘度,移印稀釋使用移印專用稀釋劑;用718洗網水清洗。

3.不得與其它類型油墨混合使用,否則容易出現其他附著力,化學反應等不良現象。

4. 加入固化劑的油墨使用時限為8小時,過期請棄用,剩余油墨不可回收

注意事項:

1.各種承印物料的外觀相似,但可能會是不同的材料,客戶需先試印,確其符合要求后,再批量生產。

2.在移印過程中,如出現拉絲或散開,可適當加入一些慢干膏即可;

3.環境溫度過高,將會影響油墨原有質量。白色超越150都會變色,烘烤時請用木質材料墊底進行烘烤,不得直接接觸鐵

4.根據氣候變化,請遠離火源,陰暗處15度-30度環境下存放

Oles MPE Plating Ink

MPE plating strengthening series ink characteristics : mainly used in plating surface, enhanced surface, vacuum plating surface.PU surface.UV surface and other materials, with a high color, high color, high covering power, high stability, high alcohol and rub characteristics. Printing: screen printing can be. Surface drying and drying time: surface dry time natural volatile 5-10 minutes; work time within 24 hours. Dilution and cleaning: SV3 slow dry open water, UVK1 ( printing open water) can be simultaneously used 718 washing network water cleaning. Test method ( completely dry ): 1, 3M gummed paper in the paintings of the surface of the ink, 45 degree angle quickly pulled off the oil; 2, 99% of the purity of industrial alcohol, one kilogram of weight of cotton pack in the ink surface, with a horizontal force pulling back and forth 200 times without decolorization; 3: oak, wear resistance eraser 500g force level brush back and forth 500 times. Usage: 1, use should be fully stirred, use at any time after the closure; 2, add water mixing 10-15%, diluted to 3, screen printing viscosity; the plug is available when washing network water cleaning; 4, not with other types of ink mixing. Note: 1, the plastic material similar in appearance, but may be of different materials, customers need to try to determine its requirements, and then batch printing; 2, in the printing process, such as drawing or spread out, may be appropriate to add some slow dry plaster; 3, the ambient temperature is too high, will affect the quality of the original ink; 4, according to climate change, please stay away from fire, dark environment storage.