PC

北?京?布?萊?迪?儀?器?儀?表?有?限?公?司

雙膜片式高靜壓差壓表

Double?diaphragm?differential?pressure?gauge

for?high?steady

YCA?標準型?Standard?style

YCAN?充液耐震型?Vibration-proof?type

PC?·03??-?1

雙膜片式高靜壓差壓表主要用于過濾器的正負壓力端，液體灌液

位、泵出入口、輸油管線、輸氣管線和加壓泵站等場合的壓力差的

測量。本儀表具有較高的耐壓性能，并適合于在有腐蝕性的環境中

使用。

Mainly?used?for?measuring?the?difference?between?two?pressure

values,?in?the?plus?and?minus?ends?of?filter,?the?level?of?liquid,?the

entrance?and?exit?of?pump,?oil?pipeline,?gas?pipeline?and?high

pressure?pump?station?and?so?on.?It?is?excellent?while?overpressure

take?place,?also?suitable?for?corrosion?environments.

產品簡介

PRODUCT

OVERVIEW

YCA

YCAN

儀表特性

●?耐壓10MPa

●?耐震型

●?長尾隔膜

●?各種安裝形式

Feature

●?Withstanding?pressure10MPa

●?Vibration-proof?type

●?Capillary?diaphragm

●?Multifold?mounting?type

PC?2008.11.6,?2:49?PM?9

BEIJING?BRIGHTY?INSTRUMENT?CO.,LTD.

MODEL?YCA?/?YCAN

技術參數?FOUNCTIONAL?FEATURES

執行標準：Q/YG?BBI009-2005?Executive?standard:?Q/YG?BBI009-2005

精度：1.6%,?2.5%?（高于0.1MPa?可選1.6級）?Accuracy:?1.6%,?2.5%

表玻璃：雙層安全玻璃?Window:?laminated?safe?glass

指針：鋁，黑色，可調零?Pointer:?aluminium,?black,?zero?adjustable

表頭形式：外徑?100，150?密閉型?干表?Case:?DS100,?150?airtight?type?dry?gauge

　　　　?。ǔ溆蚘CAN?可選）?(oil?filled?YCAN?available)

防護等級：IP65?Protection:?IP65

膜片材質：316L（負壓膜片）316Ti（正壓膜片）?Diaphragm?material:?316L（for?negative?pressure）

316Ti（for?positive?pressure）

過程連接：316?不銹鋼?Process?connection:?316

表殼材質：304?不銹鋼?Case?material:?304SS

機芯材質：304?不銹鋼?Movement:?stainless?steel?304

防爆塞和充油塞材質：耐油橡膠?The?material?of?blow?out?vent?and?filling?plug：

oil?resistant?rubber

靜壓：盤面滿量程?Steady:?full?scale?value

動壓：0.7×滿量程?Fluctuating:?0.7×?FS

過壓保護：雙邊耐壓達到?10?MPa?Overpressure?protection:?both?ends?support?10?MPa

使用溫度：－?20℃～60℃?Operate?temperature:?－?20℃～60℃

溫度漂移：隨介質溫度每變化±?10℃，?Thermal?drift:?±?0.8%?every?±?10℃?of?media

　　　　　指針指示位置漂移±0.8%?temperature

儀表量程：16KPa、25KPa、40KPa??600kPa?Range:?16KPa、25KPa、40KPa??600KPa

　　　　?。ㄒ?jiàn)規格代碼表）?(detail?in?range?table)

表連接：M20×1.5?G1/2”?NPT1/2，?Connection:?M20×1.5?G1/2”?NPT1/2，NPT1/4

　　　NPT1/4?內螺紋（不配三閥組時）另外還?thread?inside?(without?3-way?manifold)

　　　可以做成長尾法蘭連接、長尾螺紋連接、?or?capillary?connection,?capillary?threaded

　　　隔膜長尾法蘭連接（主要用于粘稠介質或?connection,diaphragm?capillary

　　　特殊材料膜片）。?flanged?connection?(mainly?used?in

viscous?medium?or?diaphragm?in?special

materials).

表盤：鋁，白地黑字?Dial:?aluminium,?white?with?black?letters

　　?。ū肀P可以根據用戶要求設計為非標形式）?(can?be?made?as?required)

儀表應配三閥組或五閥組使用。?The?instrument?should?be?used?with?3-way?manifold

group?or?5-way?manifold.

表殼充油:?YCAN?充填硅油；YCA為干式

Oil?filling:?YCAN?Silicon?filled;?type?YCA?is?dry.

PC?·03??-?2

PC?2008.11.6,?2:49?PM?10

PC

北?京?布?萊?迪?儀?器?儀?表?有?限?公?司

差壓表外形幾何尺寸?DIMENSIONS

MODEL?YCA?/?YCAN

DS100

DS150

PC?·03??-?3

注：1、差壓表的接頭可選螺紋為M20?×?1.5G1/2及?NPT1/2，如客戶有特殊螺紋要求，需要**行通知；

Note:?Differential?pressure?gauges?connection?is?optional?M20X1.5G1/2?and?NPT1/2,?if?you?have?special?request,

please?consult?with?us.

型?號?Type

幾何尺寸（mm）

fl?D1?b1?b?P1P2?L?h

fl?100?110?13?51.5

100?54?100?≈?91

fl?150?149?18?53.5

PC?2008.11.6,?2:49?PM?11

BEIJING?BRIGHTY?INSTRUMENT?CO.,LTD.

差壓表安裝幾何尺寸?Differential?pressure?gauges?dimensions

MODEL?YCA?/?YCAN

（一）?后背板安裝?Back?mounting

（二）?固定支架安裝?Steady?rest?mounting

注：1、后背板只適合平面安裝（如儀表板、機器外表平面等）；

2、注意平面要堅固，使差壓表安裝后牢固，不會發生掉落；

3、?特殊后背板可按客戶要求出圖加工或照來樣加工。

注：1、固定支架安裝只適用于管道安裝（橫向或豎向；

2、注意管道的外徑不能大于60mm；

3、?儀表可以裝到支架上方或下方，方便用戶自由選擇。

量程范圍規格代碼表?TABLE?OF?RANGES

選型代碼code?量程規格ranges?選型代碼code?量程規格ranges?選型代碼code?量程規格ranges

K110?16KPa?K192?100?KPa?K220?400KPa

K150?40KPa?K196?160?KPa?K240?600KPa

K170?60KPa?K200?250KPa?以上量程為常見量程

以上量程以外規格另行商定?other?rang?please?con?snct?with?us

PC?·03??-?4

Note:?1.?back?mounting?fit?for?plate?mounting

(instrument?plate,?and?outer?surface?etc)

2.Make?sure?the?plane?and?mount?the

differential?gauge?are?tight,?which?will?not

fall?off.

Note:?1.?Steady?rest?mounting?is?suitable?for?pipe

(horizontal?or?vertical)

2.Outer?diameter?of?pipe?cannot?over?60mm.

②?pipe?clamp

③?Steady?rest?mounting

④?Differential

pressure?gauge

⑤?vertical?pipe

①?horizontal?pipe

②?pipe?clamp

③?Steady?rest

mounting

④?Differential

pressure?gauge

PC?2008.11.6,?2:49?PM?12

PC

北?京?布?萊?迪?儀?器?儀?表?有?限?公?司

三閥組的安裝、拆卸及使用方法

Three?Valves?mounting,?disassembly?and?method?of?application

安裝?Mounting

拆卸?Disassembly

1.?正常使用差壓表必須配三閥組或五閥組以保護差壓表正常工作。

2.?差壓表和三閥組用兩個索母緊固。索母和差壓表接頭密封面應加四氟墊片。

3.?裝有三閥組的差壓表在使用前必須把中間閥門打開，并把正壓閥門和負壓閥門打

開。（當?P+和?P-?任意的壓力**入時，中間閥門能起到平衡差壓表兩腔體內的壓

力的作用，以免打壞差壓表。）

4.?當P+、P-的壓力正常進入三閥組后，再關閉中間閥門使差壓表正常工作。如差

壓表表針有輕微離零屬正常，只需把表針調到零位即可（注意必須用肥皂水檢驗所

有密封口是否泄露，如有泄露必須緊固。）

5.?差壓表有后背板式安裝（如圖）和立管固定方法。（管卡子卡到管子上）。

1.?Use?differential?gauge?must?fit?out?three?valves?in?order?to?insure?it’s?normal

working.

2.?The?differential?gauge?and?there?valves?are?connected?by?two?nuts?tightly,?nuts

and?socket?are?with?PTFEspacer.

3.?Open?the?middle?valve,?negative?pressure?valve?and?positive?pressure?valve

before?use?the?differential?gauge,?when?either?of?P-?or?P+?input,?the?middle?valve?can

have?equilibrium?activity,?and?avoid?to?damage?the?gauge.

4.?When?P-?and?P+?normal?input?the?three?valves,?the?close?the?middle?valve,?to

make?the?gauge?works?right.?If?the?gauge’s?pointer?is?not?at?zero,?please?adjust?it

to?zero?(note?must?use?soap?water?to?inspect?the?seal,?if?has?leak,?please?tight.)

5.?The?differential?pressure?gauge?has?back?plate?mounting?(see?the?chart)?and

standpipe?fixed?(the?pipe?with?clamp).

1.?首先打開三閥組的中間閥門。并打開正壓和負壓閥門（正壓負壓閥門原始為打開）

2.?關閉總進氣的兩個閥門。（在設備的主管道上）

3.?拆下更換儀表（卸兩個索母）注意用扳子卡住差壓表的接頭，只拆三閥組上的上

索母。先松開一點放空壓力，再把卡到管子上的卡子螺母松掉，并把卡子拿下。

4.?再把三閥組上的兩個索母慢慢松開把差壓表取下。?（注意一定要兩個索母同時松）

5.?把新表裝上的方法同上面安裝方法**換上兩個新的四氟墊（確保不漏）

6.?把卡子卡好

7.?先開總開關（兩個），再關上差壓表三閥組中間的閥門（新接口用肥皂水試漏）。

8.?兩分鐘后把差壓表表針調到零位。（如沒有輕微離零不用調整）

1.?Open?the?middle?valve,?negative?pressure?valve?and?positive?pressure?valve

(negative?pressure?valve?and?positive?pressure?valve?original?state?is?open).

MODEL?YCA?/?YCAN

PC?·03??-?5

①?Differential?pressure?gauge

②?Three?Valves

③?negative?pressure?valve

④?positive?pressure?valve

⑤?middle?valve

⑥?nuts

①?Upper?nut

②?Middle?Valve

2.?Close?these?two?input?valves?(on?the?main?pipe?of?equipment).

3.?Discharge?instrument?(discharge?two?nuts),?use?spanner?lock?the?socket?of?gauge,?and?just?discharge?the?nuts?on?three?valves.

Discharge?pressure,?then?put?off?the?nuts?and?clamp.

4.?Screw?down?the?two?nuts?and?take?down?the?differential?pressure?gauge?(note?screw?down?these?two?nuts?together)

5.?Then?install?the?new?gauge?(same?as?mounting?method),?change?two?spacers?to?ensure?it?will?not?leak.

6.?Fix?the?clamp.

7.?Open?main?switch?(two),?then?close?the?middle?valve.?(use?soap?water?to?inspect?leak)

8.?Two?minutes?later,?set?the?pointer?at?zero?(if?it?does?not?out?off?zero,?you?needn’t?to?adjust).

注：在裝表或卸表時，必須保證中間閥門和P+、P-兩個閥門全部開啟，以確保儀表能正常使用。

PC?2008.11.6,?2:49?PM?13

BEIJING?BRIGHTY?INSTRUMENT?CO.,LTD.

設

計

代

碼

Design

安

裝

方

式

Mounting

外

徑

Diameter

MODEL?YCA?/?YCAN

如何選型?HOW?TO?ORDER

型號代碼?特性說明

CODE?CHARACTERISTICS

YCA?（標準型）雙膜片式高靜壓差壓表

(Standard?stype)?Double?diaphragm?differential

pressure?gauge?for?high?steady

YCAN?（充液耐震型）雙膜片式高靜壓差壓表

(Vibration-proof?type)?Double?diaphragm

differential?pressure?gauge?for?high?steady

100?Ф?100mm

150?Ф?150mm

AH?徑向后背板安裝?Bottom?connection?with?back?mounting?bracket

GK?管卡子安裝?Pipe?clamp?mounting

502?內卡式不銹鋼外殼

Stainless?steel?case?Inside?bayonet

K110?16KPa?請參看量程對照表　See?range?table

M20?20×?1.5?QLA?=?長尾螺紋連接?Capillary?screw?connection

G12?G1/2?QLB?=?長尾法蘭連接?Capillary?flange?connection

Z12?NPT1/2?QLD?=隔膜長尾法蘭連接（用于粘稠介質或特殊材質膜片）

Connection?with?diaphragm

Z14?NPT1/4?TOO?=?其他特殊要求的螺紋?Other?requests

TPB?非標準的度盤?Non-standard?dial

FFA?一同裝配三閥組?Combined?with?3-way?manifold

FFB?一同裝配五閥組?Combined?with?5-way?manifold

PC?·03??-?6

基

本

型

號

Basic?type

量

程

Ranges

連

接

螺

紋

Connection

備

選

項

Options

－?·?·?·?·?·

PC?2008.11.6,?2:49?PM?14