? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 華測工頻介電常數及介質損耗測試儀HCJDCS-G




一、華測工頻介電常數及介質損耗符合標準：?
? ? ? GBT 1409-2006測量電氣絕緣材料在工頻、音頻、高頻(包括米波波長在內)下電容率和介質損耗因數的推薦方法。
? ??
二、華測工頻介電常數及介質損耗產品概述： ? ?
1、主要用于測量高壓工業絕緣材料的介質損失角的正切值及電容量。主要可以測量電容器、互感器、變壓器、絕緣紙、電容器薄膜等各種電工油及各種固體絕緣材料在工頻高壓下的介質損耗(tgδ)和電容量( Cx)，其測量線路采用“正接法”即測量對地絕緣的試品。由于電橋內附有一個2500KV的高壓電源及一臺高壓標準電容器，并將副橋和檢流計與高壓電橋有機的結合在一起，特別適應測量各類絕緣油和絕緣材料的介損(tgδ)及介電常數(ε)。
2、橋體本身帶有5kV/100pF標準電容，測量材料介損更為方便。
3、橋體內附電位跟蹤器及指另儀，外圍接線及少。
4、橋體采用了多樣化的介損測量線路。?


三、華測工頻介電常數及介質損耗技術參數：
1、測量范圍及誤差?
? ? ? ? ? ? ? ?在Cn＝100pF ? ?R4＝3183.2(Ω)(即10K/π)時
測量項目 測量范圍 測量誤差
電容量Cx 40pF--20000pF ±0.5% Cx±2pF
介質損耗tgδ 0～1 ±1.5％tgδx±1×10-4
? ? ? ? ? ? ?在Cn＝100pF ? ?R4＝318.3(Ω)(即1K/π)時
測量項目 測量范圍 測量誤差
電容量Cx 4pF--2000pF ±0.5% Cx±2pF
介質損耗tgδ 0～0.1 ±1.5％tgδx±1×10-4
?










Cx＝R4×Cn/R3
tgδ＝ω?Ｒ４?Ｃ４
高壓電源技術特性
電壓輸出：0～2500V/50Hz
高壓電流輸出：0～20mA
內置標準電容器
電容量的名義值為100pF
tgδ小于5×10-5


固體絕緣材料測試電極
本電極適用于固體電工絕緣材料如絕緣漆、樹脂和膠、浸漬纖制品、層壓制品、云母及其制品、塑料、電纜料、薄膜復合制品、陶瓷和 玻璃等的相對介電系數（ε）與介質損耗角正切值（tgδ）的測試。本電極主要用于頻率在工頻50Hz下測量試品的相對介電系數（ε）和介質損耗角正切值（tgδ）。本電極的設計主要是參照國標GB1409-2006。
本電極采用的是三電極式結構，能有效的消除表面漏電流的影響，使測量電極下的電場趨于均勻電場。?
主要技術指標
高低壓電極之間距離：0～14mm可調
測量極直徑：￠38±0.1mm
高壓電極直徑：￠56±0.1mm
測量極與保護環間隙為1±0.05
空極tgδ：≤5×10-5
**測試電壓：2kV
實驗頻率：50/60Hz
常溫或耐受溫度200℃(數字百分表不能加溫）
帶數字百分表測量范圍為0~12mm
制作技術指標依據GB/T1303.2---2009
注：原材料為不銹鋼與聚四氟乙烯，接口為與電橋配套用專用插座（帶專用插頭）。
















The frequency of dielectric constant and dielectric loss tester
A standard:
GBT 1409-2006 measurement of electrical insulating materials at power, audio, high-frequency (including meter wavelengths) recommended methods of permittivity and dielectric dissipation factor.
Two, product overview:
1, mainly used for the measurement of high voltage dielectric loss tangent of the angle of industrial insulation value and capacitance. The main measurement of capacitor, transformer, transformer, insulation paper, capacitor film and other electrical oil and all kinds of solid insulating materials in high voltage under the dielectric loss (TG delta) and capacitance (Cx), the measuring circuit adopts the "connect" to measure the insulation test. Due to the high voltage power supply bridge with a 2500KV and a high voltage standard capacitor, and the pair of bridge and the galvanometer with high voltage bridge organic unifies in together, especially suitable for the measurement of dielectric loss of insulating oil and insulation materials (TG delta) and Permittivity (epsilon).
2, the bridge itself with 5kV/100pF standard capacitance, dielectric loss measurement of material is more convenient.
3, the bridge body of potential tracker and other apparatus, external wiring and less.
4, the bridge using a dielectric loss measuring line variety.
Three, the technical parameters:
1, the measurement range and error
In the Cn = 100pF, R4 = 3183.2 (omega) (10K/ n) time
Measurement error of measurement measuring range
The capacitance of Cx 40pF--20000pF + 0.5% Cx + 2pF
The dielectric loss TG delta 0 ~ 1 + 1.5%tg + 1 * 10-4 X.
In the Cn = 100pF, R4 = 318.3 (omega) (1K/ n) time
Measurement error of measurement measuring range
The capacitance of Cx 4pF--2000pF + 0.5% Cx + 2pF
The dielectric loss TG delta 0 ~ 0.1 + 1.5%tg + 1 * 10-4 X.
Cx = R4 * Cn/R3
Delta = Omega TG? R4? C4
The technical characteristics of the high voltage power supply
Output voltage: 0 ~ 2500V/50Hz
High voltage current output: 0 ~ 20mA
The built-in standard capacitor
Nominal capacitance value is 100pF
TG is less than 5 * 10-5.
Solid insulating materials testing electrode
The electrode for solid electrical insulating dielectric coefficient materials such as insulation paint, resin and rubber, impregnated fiber products, laminated products, mica and its products, plastic, cable materials, thin film composite products, ceramics and glass, (E) and dielectric loss tangent (TG delta) test. The electrode is mainly used for relative dielectric constant measurement of frequency in the frequency of 50Hz of the sample (s) and dielectric loss tangent (TG Delta). The design of the electrode is mainly refer to the national standard GB1409-2006.
The electrode is used in the three pole type structure, can effectively eliminate the influence of surface leakage current, the electric field measurement electrode under uniform electric field.
The main technical indicators
The distance between the high voltage electrode: 0 ~ 14mm adjustable
Measurement of diameter: 38 + 0.1mm
The high voltage electrode diameter of 0.1mm: 56.
Measurement and protection ring gap is 1 + 0.05
The air is less than 5 * 10-5 TG Delta.
The maximum test voltage: 2kV
Test frequency: 50/60Hz
At room temperature the temperature of 200 DEG C or tolerance (digital indicator can\'t heating)
With digital dial indicator measuring range is 0~12mm
Production of technical indicators based on GB/T1303.2---2009
Note: the raw material is stainless steel with PTFE, interface and bridge supporting the use of the special socket (with a special plug).